DHCP server installation

Dynamic Host Configuration Protocol.

Note:

Since Ubuntu 11.10 the DHCP3-server is available in the "isc-dhcp-server" package.

Sources

You can find more information about that topic over here:

• http://doc.ubuntu-fr.org/dhcp3-server
• https://wiki.debian.org/PXEBootInstall

Requirement

A DHCP server can provided static or dynamic address.

However, the DHCP server's IP @ must always be static!!

If you want to use a DNS, then you can even setup the DNS server first. See DNS server

Installation

DHCP server

apt-get install isc-dhcp-server

You will be asked a few questions:

• On what network interfaces should the DHCP server listen? <-- eth0
• Please configure the DHCP server as soon as the installation finishes. <-- Ok
• The version 3 DHCP server is now non-authoritative by default <-- Ok

At the end of the installation you will see errors like these: * Generating /etc/default/dhcp3-server...

• Starting DHCP server: dhcpd3 failed to start - check syslog for diagnostics.
• invoke-rc.d: initscript dhcp3-server, action "start" failed.

That's OK because we did not have the chance yet to configure our DHCP server.

Security

You should edit your firewall to match the current rules:

    IPTABLES=`which iptables`
    LAN_ADDRESS="192.168.2.0/24"

    # Allow LAN communication
    # ... Required for NFS and the NetBoot ...
    $IPTABLES -A INPUT -s $LAN_ADDRESS -d $LAN_ADDRESS -m state ! --state INVALID -j ACCEPT
    $IPTABLES -A OUTPUT -s $LAN_ADDRESS -d $LAN_ADDRESS -m state ! --state INVALID -j ACCEPT

    ########################
    # INPUT filters
    ########################

    ##### DHCP client ######
    # Broadcast IP request 
    $IPTABLES -A OUTPUT -p udp -d 255.255.255.255 --sport 68 --dport 67 -j ACCEPT
    # Send / reply to IPs requests
    $IPTABLES -A INPUT -p udp -s 255.255.255.255 --sport 67 --dport 68 -j ACCEPT

    ###### DHCP server ######
    # UDP (can also run on TCP) >> received client's requests
    $IPTABLES -A INPUT -p udp --sport 68 --dport 67 -j ACCEPT
    $IPTABLES -A INPUT -p tcp --sport 68 --dport 67 -j ACCEPT

    # NetBoot - TFTP server
    $IPTABLES -A INPUT -p udp -s $LAN_ADDRESS --dport 69 -j ACCEPT


    ########################
    # OUTPUT filters
    ########################
    # DHCP [udp]
    $IPTABLES -A OUTPUT -p udp --dport 67 -j ACCEPT
    $IPTABLES -A OUTPUT -p udp --dport 68 -j ACCEPT
    # DHCP [tcp]
    $IPTABLES -A OUTPUT -p tcp --dport 67 -j ACCEPT
    $IPTABLES -A OUTPUT -p tcp --dport 68 -j ACCEPT

    # TFTP NetBoot 
    $IPTABLES -A OUTPUT -p udp --dport 69 -j ACCEPT

Don't forget to adjust your network number 192.168.2.0/24

Configuration

The main configuration file is /etc/dhcp/dhcpd.conf

vim /etc/dhcp/dhcpd.conf

You can adjust the interface the server is listening on in /etc/dhcp/dhcp3-server INTERFACES="eth0 eth1"

Random IP assignation

The following configuration will accept all clients and give them a random IP @.

# Sample /etc/dhcpd.conf
# (add your comments here) 
default-lease-time 600;
max-lease-time 7200;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.100.255;
option routers 192.168.100.254;
# Put your own DNS server or your ISP | Google servers
option domain-name-servers 192.168.100.1, 192.168.100.2;
# Put your domain name - if you have one
option domain-name "mydomain.lan";
option ntp-servers 192.168.100.254;

subnet 192.168.100.0 netmask 255.255.255.0 {
  range 192.168.100.10 192.168.100.100;
  range 192.168.100.150 192.168.100.200;
}

You have to adjust:

• Network parameters - instead of 192.168.100.*
• DHCP range(s). In the given example there are 2 ranges from 10-100 and 150-200

Static IP @

This new configuration will ONLY accept known clients and give them a static IP @.

# Sample /etc/dhcpd.conf
# (add your comments here) 
default-lease-time 600;
max-lease-time 7200;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.100.255;
option routers 192.168.100.254;
option domain-name-servers 192.168.100.1, 192.168.100.2;
option domain-name "mydomain.lan";
option ntp-servers 192.168.100.254;

deny unknown-clients;

subnet 192.168.100.0 netmask 255.255.255.0 {
    host client1 {
        hardware ethernet DD:GH:DF:E5:F7:D7;
        fixed-address 192.168.100.20;
    }
    host client2 {
        hardware ethernet 00:JJ:YU:38:AC:45;
        fixed-address 192.168.100.21;
    }
}

Note:

The deny unknown-clients; command is why only known clients are accepted.

For each client you have to adjust:

• MAC @
• Set a specific static IP @

Advanced configuration (name + netboot)

In the following scenario you will configure the server to accept only specific clients, use static IP @ and set names.

This configuration also allow NetBoot using PXE technology.

#### General options ####

## Domain settings
# domain name
option domain-name "myDomain.lan";
# DNS IP @ (replace it by your IP server, Google DNS or your ISP DNS) 
option domain-name-servers XXX.XXX.XXX.XXX, YYY.YYY.YYY.YYY;
# DNS update system (disable)
ddns-update-style none;

## IP lease settings
default-lease-time 7200;
max-lease-time 86400;

## Network settings
# DHCP server name
server-name "dns.myDomain.lan";
# Authoritative server = this is the official DHCP server for the local network
authoritative;
# Subnet-mask
option subnet-mask 255.255.255.0;


## Security
# Do not allow unknown clients 
deny unknown-clients;
# Do not forward DHCP request from this server to another one using a different Network Interface
option ip-forwarding off;

# Use this to send dhcp log messages to a different log file 
# you also have to hack syslog.conf to complete the redirection
log-facility local7;

### NetBoot PXE
# Enable network boot using TFTP 
allow bootp;
allow booting;


## Available networks

# Your server can manage many network. Just add new subnet{} instruction

# Main LAN
subnet 192.168.100.0 netmask 255.255.255.0 {
  #### Overall settings
  # You can override the default domain set earlier
  option domain-name "myDomain.lan";
  # Broadcast address
  option broadcast-address 192.168.100.255;
  # Default gateway
  option routers 192.168.100.1;
  # Set the NTP (time server) to use
  option ntp-servers 192.168.100.1;


  #### DHCP range
  # Hint: if the range has only 1 address, and this is a bail (fixed address), then the range won't be used!
  range 192.168.100.5 192.168.100.5;

  #### NETBOOT settings 
  # PXE file to serve.
  #   >> elilo.efi   => for ia64 clients; 
  #   >> pxelinux.0  => for x86
  # These files should be at the root of your TFTP server
  # Note: The file name can be add in the "host" section too. Then, the "host" will override the current setting
  filename "pxelinux.0";
  # set the server that serve this NETBOOT file
  next-server 192.168.100.2;
  # Ensure that the new client (the one boot) is not stealing someone else IP @
  ping-check = 1;
}

#### Managed host and fixed IP @
# FTP server
host ftp {
  hardware ethernet 00:0f:75:af:eb:44;
  fixed-address 192.168.100.2;
  option host-name "ftp";

  ### NetBoot PXE settings
  # dedicated file for the current machine:
  #filename "debian-installer/ia64/elilo.efi";
  # Set the TFTP server
  #next-server 192.168.100.2;
} 
# WEB server
host web {
  hardware ethernet 00:02:0d:31:d1:cc;
  fixed-address 192.168.100.3;
  option host-name "web";
}
# EMAIL server
host mail {
  hardware ethernet 00:02:55:d2:d1:cc;
  fixed-address 192.168.100.4;
  option host-name "mail";
}
# LAPTOP workstation
host laptop {
  hardware ethernet 00:0e:af:31:d1:cc;
  fixed-address 192.168.100.5;
  option host-name "laptop";
}

Be aware that the "option host-name ..." may be discard by most clients.

Logs

Logs are in /var/log/syslog

Leases

All DHCP leases are available in:

vim /var/lib/dhcp3/dhcpd.leases

Manage service

You can start / restart service using:

service isc-dhcp-server start|restart|stop

OR

/etc/init.d/isc-dhcp-server restart

You can check the status using:

ps aux | grep dhcp
netstat -uap | grep dhcp

Add new host

Every time you need to install you host you have to:

Edit the configuration file:

vim /etc/dhcp/dhcpd.conf

Add new host at the end of the file :

host myNewHost {
  hardware ethernet 00:0e:af:31:d1:cc;
  fixed-address 192.168.100.60;
  option host-name "myNewHost";
}

Restart the DHCP server :

/etc/init.d/isc-dhcp-server restart

NetBoot

To setup the netboot, see NetBoot server.